$94.33 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location:
Ships to: US,
Item: 395012732276
eBay 1.Fit For 1998 – 2002 Ford CROWN VICtoRIA All Models 1998 – 2002 Lincoln toWN CAR All Models 1998 – 2002 Mercury GRAND MARQUIS All Models 2.Package Includes: 2x Part# Front Stabilizer/Sway Bar Links – K8953 2x Part# Rear Stabilizer/Sway Bar End Links – K8848 2x Part# Front Upper Ball Joints – K8678 2x Part# Front Lower Ball Joints – K8685 1x Part# Front Pitman Arm – K8688 1x Part# Front Idler Arm – K8283 For Town Car & Crown Victoria 16x Front Ball Joints Tie Rods Pitman Arm Sway Bar 1.Fit For 1998 – 2002 Ford CROWN VICtoRIA All Models 1998 – 2002 Lincoln toWN CAR All Models 1998 – 2002 Mercury GRAND MARQUIS All Models 2.Package Includes: 2x Part# Front Stabilizer/Sway Bar Links – K8953 2x Part# Rear Stabilizer/Sway Bar End Links – K8848 2x Part# Front Upper Ball Joints – K8678 2x Part# Front Lower Ball Joints – K8685 1x Part# Front Pitman Arm – K8688 1x Part# Front Idler Arm – K8283 2x Part# Front Inner Tie Rods Ends – ES3494 2x Part# Front Outer Tie Rods Ends – ES3495 2x Part# Front Tie Rod Adjusting Sleeves – ES3311 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle Front Type Sway Bar Link Universal Fitment No Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K8848 ES3494 ES3495 K8678 K8685 ES3311S K8283 K8688 K8953 OE/OEM Part Number Suspension Steering Tie Rod Ends Linkages Assembly,Ball Joint Superseded Part Number Front/Rear Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand sztautopartstore Manufacturer Part Number E81110101CP Greasable or Sealed Greasable Modified Item Yes OE Spec or Performance/Custom OE Spec Surface Finish Polished, Rust Protected Quantity 16 Pcs Cross Part Number 15963924, 25747956, 4656260AA, 6W1Z5664AA, F0VY5A486A Kit Parts Included Ball Joint, Sway Bar,Outer Tie Rod, Inner Tie Rod,Control Arm Cross Reference Part Number 1998 1999 2000 2001 2002 Cross Reference Part Number For Ford & Lincoln & Mercury Suspension Grade Standard Position for driver & passenger side, front suspension kit Store Speciality Suspension & Steering Features Greasable Finish Coated Material Alloy Steel Mounting Style Bolt-On Cotter Pin Hole Yes Shipping * Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. * All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in ab out 3-5 business days. * We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if i t is different from the one in eBay. * The tracking number will be given for the customer to check the shipping status online (registered or faster service only). * We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Return/Refunds * You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! * All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. Feedback * We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. * It is impossible to address issues if we do not know about them! Warranty policy WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. * We stand behind every product we sell. * All of our brand new items come with a 60-Days money-back guarantee. * We define the item as defective only if it doesn’t function as described. * It is the buyer’s responsibility to understand the item description before bidding. * We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. * We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. * Shipping & handling cost are not refundable. * Man-made damage by abuse or wrong operation is not covered by this warranty. * No product liability insurance is assumed. Payment PayPal preferred. *Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Payment Shipping Return policy Feedback Contact us Shop Category Store Home Car & Truck Brake Rotors & Pad Car & Truck Brake Pads Car & Truck Calipers & Bracket Car & Truck Brake Drum & Shoe Car & Truck Brake Shoes Car & Truck Brake pad sensor Suspension Kit Other Hot Item New List Item Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us For Town Car & Crown Victoria 16x Front Ball Joints Tie Rods Pitman Arm Sway Bar 1.Fit For 1998 – 2002 Ford CROWN VICtoRIA All Models 1998 – 2002 Lincoln toWN CAR All Models 1998 – 2002 Mercury GRAND MARQUIS All Models 2.Package Includes: 2x Part# Front Stabilizer/Sway Bar Links – K8953 2x Part# Rear Stabilizer/Sway Bar End Links – K8848 2x Part# Front Upper Ball Joints – K8678 2x Part# Front Lower Ball Joints – K8685 1x Part# Front Pitman Arm – K8688 1x Part# Front Idler Arm – K8283 2x Part# Front Inner Tie Rods Ends – ES3494 2x Part# Front Outer Tie Rods Ends – ES3495 2x Part# Front Tie Rod Adjusting Sleeves – ES3311 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. ShippingReturn/RefundsFeedbackWarranty policyPayment * Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. * All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in ab out 3-5 business days. * We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if i t is different from the one in eBay. * The tracking number will be given for the customer to check the shipping status online (registered or faster service only). * We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. * You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! * All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. * We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. * It is impossible to address issues if we do not know about them! WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. * We stand behind every product we sell. * All of our brand new items come with a 60-Days money-back guarantee. * We define the item as defective only if it doesn’t function as described. * It is the buyer’s responsibility to understand the item description before bidding. * We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. * We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. * Shipping & handling cost are not refundable. * Man-made damage by abuse or wrong operation is not covered by this warranty. * No product liability insurance is assumed. PayPal preferred. *Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. All rights reserved.
Frequently Asked Questions About For Town Car & Crown Victoria 16x Front Ball Joints Tie Rods Pitman Arm Sway Bar in My Website
www.archfrancescana.org is the best online shopping platform where you can buy For Town Car & Crown Victoria 16x Front Ball Joints Tie Rods Pitman Arm Sway Bar from renowned brand(s). www.archfrancescana.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling For Town Car & Crown Victoria 16x Front Ball Joints Tie Rods Pitman Arm Sway Bar on www.archfrancescana.org?
www.archfrancescana.org helps you to shop online and delivers Kappa to your doorstep. The best-selling Kappa on www.archfrancescana.org are: NWT KAPPA AUTHENTIC BLACK SHERPA SWEATSHIRT HOODIE LONG SLEEVE SHOWFLAKE size S Kappa Mens Ruiz Long Sleeve Shirt Large Green Graphic Sleeve Hit Crew Neck Logo ! FREE SHIPPING Blackburn Rovers FC KAPPA 2000 Football Soccer Jersey Adults s M KAPPA AUTHENTIC ESMIO Men’s Kappa Black Sweat Shorts Pull On Drawstring Activewear Training Sz S Gosha Rubchinskiy x Kappa Fashion Mesh Tank Top Black Size L RARE Kappa 222 Banda Anniston Track Jacket Petrol-Pink Size Small Regular Fit Kappa Hoodie Sweater “TIEANDYE” Size Small Robe Di Kappa Brand New Authentic KAPPA Joggers Men Size L Olive Sweatpants Side Pockets Zip-Ankles Gym Casual Gym Pi Kappa Phi Join Or Die Bella + Canvas POCKET T Shirt Pi Kapp Frocket Tee NEW KAPPA MENS LONG SLEEVE WHITE/RED MEDIUM SHIRT Kappa tennis club short sleeve crewneck tee white t-shirt regular fit mens 2XL Kappa Gumball 3000 Carrera Hot Wheels Jersey Adult Large Nice! Aston Villa Training Jacket Long Sleeve Blue Kappa Mens Size 2XL ig93 Manchester City | Men’s Medium Retro Jersey 90s Rare Kappa Juventus Vintage 90s Heavy Jacket Men’s Kappa Termo Black Size: M Kappa Alpha Psi Frat Shirt Size Extra Large XL Polo Kappa Active LOGO TAPE Side Pocket ALIC 2 TRACKPANTS Jogger Sweatpants New LEEDS UNITED KAPPA TRAINING TOP FOOTBALL SHIRT 2017-18 SOCCER JERSEY BLUE MEDIUM Phi Sigma Kappa – Chi Omega Short Sleeve T-shirt, Orange, 100% Cotton, Size M Limit to 500 Van Basten #9 AC Milan 1988 1989 Original Home Jersey Kappa Size XL Vintage Kappa Myrtle Beach Long Sleeve T Shirt Spellout Mens Large White USA Y2K Kappa Brazil Soccer T-SHIRT Embroidered Med NWT KAPPA AUTHENTIC PANTHERS UNIVERSITY HOODIE MENS MEDIUM BURGUNDY Kappa Shorts Mens Medium Black Work Out Gym Basketball Shorts Elastic Waist Vintage Kappa Puffer Vest XXL Black Green Down Puffer Kappa Italy Sport Hooded Black & Orange Size Large Hoodie KAPPA Jacket Mens Small S Black Yellow Logo Spell Out Full Zip Quilted Kappa Juventus Team T-Shirt Polyester Men Size XL White Striped Vintage Kappa Rolling Loud Miami Pullover Hoodie Men Medium White SIZE 2XL Kappa Mens 222 Banda Benettin 2 VELOUR TRACK JACKET BLACK JUVENTUS #11 KAPPA PRO SOCCER TSHIRT Sz L VTG BLACK PEPSI SPONSOR BRAND NEW TAGS Kappa Jacket Mens Large Windbreaker Blue Coat Half Zip * Kappa Sportswear Authentic Ruiz 2 White Black Sport Men XL X-Large Long Sleeve KAPPA Navy Vintage 90s zip fleece jacket SZ Medium (G9205) KAPPA TRACK JACKET MEDIUM M MENS BLACK TAPE LOGO FUTBOL SOCCER FULL ZIP VINTAGE 2005 Pies For Push Pi Kappa Phi Concert Festival College Shirt Y2K S Small Robe Di Kappa Mens Giovanni Varsity Jacket Black White Sz XL Brand New w/out Tag Kappa Japan Tracksuit Pant And T Shirt Large Men’s Yokai Shop Kappa No Sanpei Sweatshirt Adult Large Fits Medium Gray Mizuki Anime Kappa Training Shirt Men’s Large Gray Heather Knit Activewear Tee Kappa 222 Banda Tape S Track Pants Men’s Green Sage Slim Fit Athleisure NWT Real Betis Kappa Away Soccer Jersey Shirt EU XL US Large 20/21 NWT Joaquin #17 Kappa 222 Reflective Michael Tee Men’s Size L Short Sleeve T-shirt Yellow Logo Kappa Hoodie Mens Small Brown Graphic Logo Pullover Sweatshirt Sweater Kappa – US Ski Team ESTESSI Embroidered Logo Patch T-Shirt MENS BLACK – XXL 2XL Kappa Gumball 3000 Sanzen Japan Full Zipper Jacket Sweatshirt White #20 Red XL Kappa Logo Tape Apet 2 Mens Small Indigo Blue Regular Fit Hoodie Sweatshirt Aston Villa Shirt Kappa Blue Large Football Shirt Jersey Training Shirt Villa KAPPA Mens T-Shirt Black Crew Neck M Kappa Jacket Vintage Rainbow Color size Medium # 174934 Old Style Full Sleeves VINTAGE Kappa Polo Shirt Men’s Small Blue Tennis Short Sleeve Logo Kappa Sweater Mens Medium Gray Crew Neck Long Sleeve Embroidered Logo Pullover Kappa T Shirt Mens Large Blue Big Spellout Soccer Short Sleeve Premium Cotton Vintage Kappa Sigma Fraternity T-Shirt Size L 1985 Step Sing Single Stitch Robe di Kappa Tshirt Size Large NWT NAPOLI FC KAPPA GARA 2018 2019 HOME EUROPEAN JERSEY SIZE L Kappa Authentic Vasco da Gama Brazil 2024 Away Soccer Jersey Men’s Sz: XL NWT AUTHENTIC Kappa Fiorentina 2020-21 Snapback Hat KAPPA 222 BANDA ALANZ-2 Drawstring SWEATPANTS 311BHCW-A4F New Napoli Kappa Men Player Top T-Shirt Short Sleeve Navy Blue Football Running XL Popular Demand “TIGER” / Kappa Hoodies Black-Red Lot Of 2 Men’s Size Small Kappa Sweater Di Kappa Mens XL Wool Knit Crewneck Jumper Pullover Blue USA Flag Kappa Track Pants Red White Stripe Men Size Medium Perfect Condition Kappa 222 BANDA AFIEN 1/4 ZIP REFLECT Jacket Front Pocket Track Medium Running Delta Kappa Gamma Crewneck Made In USA Jerzees Large White Vintage Kappa Sports Track Jacket Orange XL Long Sleeve Zip Up Kappa Hoodie Sweater XS Green RARE Authentic Reflective Logo kappa hoodie Size XL Kappa Mens Graphic Tee Tshirt 2XL Beach Outdoors Camp Relax Short Sleeve Friends Kappa Men’s Banda Vulki Fuchsia Shirt Short Sleeve Pink Summer Shirt (XL) $55 tg Kappa Hoodie Small Mens Black Pullover Drawstring Graphic Print Cotton Polyester ITALIA KAPPA TRAINING TRACKSUIT-for people who wears size LARGE Kappa Jacket Adult SMALL Black Graphic Logo Long Sleeve Full Zip Classic Unisex kappa track pants men KAPPA Joggers Sweatpants Maroon Flex Waist Drawstring — Size L Venezia FC 2023/2024 Kappa Third Blue Jersey Long Sleeve M-3XL NWT w/ Bag ASTON VILLA 2021/2022 HOME FOOTBALL SHIRT JERSEY KAPPA SIZE M BOYS Kappa Sweatpants Trousers Women L Red Athletic Striped Drawstrings Patch Logo Kappa Authentic Vasco da Gama Brazil 2024 Soccer Jersey Men’s Sz: XL KAPPA Men’s Shirt Sleeve Logo Taping Logo Blue Gray Size M Reflective Kappa Zip Up Track Suit Jacket – Small Kappa AUTHENTIC FOOTBALL ERIN TRACKPANTS 3116LUW-A03 Blue Turkis-Black-W New Kappa Shirt Mens Size M/L Blue Workout Performance Gym Stretch Training *READ* Vintage Kappa Silver Pullover Sweatshirt with Pockets XL Kappa track jacket blue black size small KAPPA ROYAL BLUE SHINY SILKY SOCCER FOOTBALL SHORTS – SIZE MEDIUM Vintage 1999 KAPPA Vasco Da Gama Soccer Football Polo T-Shirt Jersey L VTG ACE kappa RETRO STYLE Barcelona (Barça) 93/95 HOME Men’s Jersey – Size L (fits M) AUTHENTIC Kappa Sassuolo 2015-16 Long Sleeves Polo – Men (M) LEEDS UNITED FOOTBALL SOCCER SHORTS 100 YEARS CANTENARY KAPPA GARA sz L MEN BLUE Kappa men’s slim fit black track jacket large full zip Kappa Black and Gray Bomber Kappa Fleece 1/4 Zip Sweatshirt Mens XL Grey Round Texel Catamaran Regatta Race Kappa Track Jacket Men’s Size 3XL Black Black Violet 222 Banda Anniston – NEW Vintage Shirt Kappa Alpha Psi Fraternity Crew Neck Sweatshirt 1960? Old! Kappa Rogue Valley Soccer Club Soccer Jersey Number 10 Size L Kappa men’s logo tape artem 2 track jacket in Multi – size 2X Kappa Varsity Jacket Xl Mens Pullover Fleece Hoodie
